FM1202
FM1202FM1202FM1202

FM1202 – IP67 and NiMH battery

Waterproof GPS/GSM vehicle tracker with Nickel Metal Hydride back-up battery

Technology
  • SMS
  • GPRS
  • GNSS
Hardware
  • 6 - 30V
  • 16MB memory
  • IP67
  • Battery
Firmware
  • Anti-jamming detection
  • Eco driving
  • Immobilizer

Compare products
(Compare 2 or up to 4 products)

Product Description

Waterproof GPS/GSM vehicle tracker

  • Waterproof case with IP67 rating
  • Internal High Gain GSM and GPS/GLONASS antennas
  • Integrated NiMH (400 mAh) back-up battery
  • Large Flash memory (16MB!)
  • Integrated scenarios: Overspeeding, Authorized driving and Immobilizer

FM1202 Scheme

FM1202T27DSC* package contains

  • FM1202 tracker
  • Micro USB – USB cable (0.8 m)

* SAMPLES ordering code – applied for orders up to 7 pcs.

FM1202T27D01* package contains

  • FM1202 tracker
  • Micro USB – USB cable (0.8 m)

* MASS PACKAGING – for bigger quantity orders, with configuration cable included.

FM1202T26A01* package contains

  • FM1202 tracker

* MASS PACKAGING – for bigger quantity orders, configuration cable not included.

  • TECHNOLOGY

  • GNSS i Global positiong system/Global Navigation Satellite System.
  • GPRS i General Packet Radio Service (GPRS) is a packet oriented mobile data service based on the 2G technology.
  • SMS i Short Message Service (SMS) is a text messaging service component.
  • HARDWARE

  • Internal GSM antenna i An antenna used for GSM connectivity. Integrated into FM device PCB. Does not have external connector.
  • Internal GNSS antenna i An antenna used for GPS connectivity. Integrated into FM device PCB. Does not have external connector.
  • DIN – digital input –2 i Digital Inputs allow device to detect logic states 1 (enabled) or 0 (disabled).
  • AIN - analog input –1 i An analog input converts a voltage level into a digital value that can be stored and processed in device.
  • DOUT –2 i Digital Outputs allow device to output logic states 1 (makes a circuit) and 0 (cuts the circuit).
  • 1-Wire® –1 i 1-Wire® is a device communications bus system that provides low-speed data, signaling, and power over a single conductor.
  • Accelerometer i Accelerometer allows the device to indicate if vehicle is
    moving or not, as well as measure acceleration.
  • Battery –400mAh Ni-MH 7,2V i Allows device to work without external power source
  • IP67 i Protected from total dust ingress, immersion between 15 centimeters and 1 meter in depth.
  • 16MB memory i Internal memory for records storing when there is no GPRS connectivity.
  • 6 - 30V i External voltage range
  • Overvoltage protection i Protects device from voltage jumps till 90V
  • 1x SIM Card i Allows to put 1 SIM card for internet connection
  • Outdoor casing i Enclosure which lets keep device outside safely
  • USB 2.0 Interface i Device accessible and configurable via USB
  • FIRMWARE

  • Ignition detection i A vehicle ignition detection function, based on a configured ignition source (External power voltage, Digital input 1 or Movement).
  • Geo-fence i A functionality, which generates an event when crossing a defined area. It can be used to detect wherever car enters or leaves customized areas
  • Sleep/Deep sleep i Working modes which let FM device to reduce power consumption and save vehicle battery.
    - In sleep mode, FM device turns GNSS module off and it is not saving or sending new periodic data records.
    - In deep sleep mode, FM device sets GNSS receiver to sleep mode and turns off GSM/GPRS module, although periodic records with last known coordinate are being saved and sent to server.
  • Overspeeding detection i This scenario helps to prevent from exceeding fixed speed and inspects driver if needed. Digital output 1 is controlled by scenario for user needs, to manage buzzer, LED etc. During overspeeding event Digital output 1 will be turning ON and OFF until speed is lower than configured Max Allowed Speed.
  • FOTA i Firmware over the air solution. The software is used to send firmware/configuration to FM device via GPRS network.
  • Remote Log i This type of FM data logging is used when there is no possibility to connect to device physically. Device establishes GPRS connection and activates link to server, log is started to stream to server until set time is elapsed.
  • GPRS commands i It is possible to send commands to FM device using GPRS. GPRS commands can be used for sending configuration, debug, digital outputs control commands etc. These commands should be coded into a special codec12 format.
  • RFID 1-Wire® i Radio-frequency identification (RFID) is the use of a wireless non-contact system to transfer data from a tag attached to an object, for the automatic driver identification. Reader can be connected to FM device via 1-wire interface.
  • iButton 1-Wire® i iButton is a special driver identification chip based on 1-wire protocol. External 1-wire iButton reader can be used in parallel with FM devices
  • Temp. 1-Wire® i A temperature sensor which can be connected to FM device and provide information via 1-wire data protocol.
  • Immobilizer i With this scenario vehicle can be used only if iButton is connected. You can connect any iButton to pass Immobilizer security. FM device Digital Output 2 is controlled by scenario for user needs (for example: LED, buzzer or other indicator can be connected).
  • Eco driving i This scenario helps to prevent and inspect driver about harsh driving. Eco driving scenario continuously monitors: accelerating, braking and cornering forces depending on build in accelerometer. Monitoring sensitivity is configurable.
    FM device Digital Output 1 is controlled by scenario for user needs, buzzer or LED for example.
  • Anti-jamming detection i Jamming detection informs the driver with buzzer or LED about radio jamming events.
  • SMS event i SMS event is a special functionality which is used to notify the user about the tracker initial state. Any changes of speed, engine status, over speeding or etc. will be informed with SMS.
  • Odometer i Odometer is used to calculate traveled distance and produce this information directly to server.
  • Trip detection i Trip detection is used to inform user about start and stop points in the dedicated location, while engine is on or off.
  • Integrated scenarios i The integrated device scenarios are used to simply enable the dedicate functionality like Green driving, Over speeding, Authorized driving or Immobilizer.
  • Remote configuration over SMS i The remote configuration via SMS gives an ability to configure the device via SMS
  • Offline tracking i Offline tracking is used to track the object position while GPRS is not activated.
  • Auto Geofencing i Auto geofencing can detect wherever car enters or leaves customized areas with deactivated ignition.

Technical details

GSM:

  • Quad-band 900/1800 MHz; 850/1900 MHz
  • GPRS class 10 (up to 85,6 kbps);
  • SMS (text/data)

GPS:

  • NMEA, GGA, GGL, GSA, GSV, RMC, VTG protocol compatible
  • 32 channel GPS/GLONASS receiver
  • -161 dBm sensitivity

Interface:

  • 1 Digital Input Reserved for Ignition Status Monitoring
  • 2 Digital Inputs
  • 1 Analog Input (10V or 30V range)
  • 2 Digital Open-collector Outputs (connecting external relays, LED, buzzers etc.)
  • 1-Wire® protocol
  • Power supply (+6…+30)VDC
  • 2 Status LEDs
  • Configuration and firmware upload (FOTA and via cable)

Features:

  • Hermetic enclose IP67
  • Internal High Gain GSM antenna
  • Internal High Gain GPS/GLONASS antenna
  • GPS/GLONASS and I/O data acquisition
  • Real Time tracking
  • Smart data acquisition (based on time, distance, angle, ignition and events
  • Sending acquired data via GPRS (TCP/IP and UDP/IP protocols)
  • Smart algorithm of GPRS connections (GPRS traffic saving)
  • Operating in roaming networks (preferred GSM providers list)
  • Events on I/O detection and sending via GPRS or SMS.
  • Scheduled 24 coordinates SMS sending
  • 5 geofence zones (rectangular or circle)
  • Deep Sleep mode (less power consumption)
  • FOTA (firmware updating via GPRS)
  • Motion sensor
  • Small and easy to mount case
  • 3 operational modes (Home, Roaming, Unknow) based on operator
  • Operation mode presets:
    • Advanced overspeeding detection
    • Driver identification (1-Wire® iButton ID key)

Downloads